Quality assurance with Berdan 27 January 2020

For forty years Mr Hasan Şemsi has directed and inspired the development of Berdan Cıvata, based in the ancient city of Tarsus, in south-east Turkey. Here he talks about how a small business grew to be a fully integrated production operation and, remarkably candidly, of the mistakes that taught him how to achieve the highest levels of quality assurance for critical application construction fasteners.

In Turkey in the 1980s, an employee who had worked for 15 years over a 25 year period was entitled to retire. That is how I was able to retire from Temel (STFA) Bolt, then the biggest bolt factory in Turkey, aged 43 and join my brother, Yunus, in setting up a 200m2 workshop in Tarsus with five employees.

We realised that we had no possibility to be competitive in low strength bolts so we needed to produce high value-added bolt and nuts. At our workshop, the bolts were hot forged and the threads either machined or rolled. Then they had to be taken to a company 40km away for quenching and tempering. Then they were shipped 450km to Ankara for hot zinc coating. Finally, they were tested by a state institution in Adana, around 40km from our workshop.

I already had twelve years’ experience in the bolt and nut sector, half of it in business management at the oldest and biggest bolting factory, called Denet Civata, in Istanbul, and the rest at Temel Bolt, in Adana. I had gained a great deal of knowledge about bolts, nuts, materials, surface coatings, heat treatment and testing. However, we still had things to learn and in some cases we had to learn expensive lessons.

We gained our first lesson by sending two containers of bolts, destined for a power plant in Ankara, to a coating company for hot dip galvanising. However, we did not realise that while this company had coated thousands of Class 5.8 bolts every year, it had insufficient knowledge and experience in coating Class 10.9 bolts like these. We were informed that our precious 10.9 quality bolts had been cleaned by acid pickling in the same way as the low strength 5.8 quality bolts. Obviously, by keeping them in acid for a long period of time, they had all been exposed to the risk of hydrogen embrittlement. As a result, we had to scrap all the bolts and produce new ones to replace them.

We carried out more research on Class 10.9 and 12.9 after this heavy loss, equivalent to nearly one year of earnings for the 10 – 12 employees in our small and new business. The ASTM F568 standard, which confirmed our own belief, recommended that Class 10.9 or 12.9 bolts should not be hot dip galvanised (HDG), because of the risk of embrittlement failure as a result of the hydrogen introduced to the steel while pre-cleaning with acid.

However, on some big projects abroad we saw exactly these grades of bolts covered with HDG. So we thought if this could be done outside of Turkey we should be able to coat our bolts in a similar way. Finally, through careful research and testing we achieved a safe methodology.

Now, in our eco-friendly HDG facility, we protect both the health of our employees and the environment by performing mechanical cleaning instead of pre-cleaning with acid. Most importantly the bolts are not exposed to the risk of hydrogen brittleness. We have took out a patent for this methodology and started declaring to our users, through trade fairs and professional publications, that the hydrogen embrittlement risk on 10.9 hot dip galvanised bolts has been eliminated by Berdan FOREVER at our eco-friendly coating premises.

This announcement was so effective that we rapidly needed to increase our capacity by two or three times with this coating method making such a great contribution to our growth. By these operations we realised that there have been so many steel fastener users, both domestically and outside of our country, suffering from hydrogen fragility.

We received our second hard lesson from our heat processor. We learned that it had hardened the Class 10.9 bolts we had produced from 42CrMo4 material by heating them in a rich carbon semiconducting cabinet, instead of hardening in a neutral bath. Because of the heating in this abundant carbonaceous salt bath, carbon deposits in the valley of our bolt threads developed.

These 10.9 bolts were used in a 50m – 60m high tower. The tower, which was to be lifted to the top of a building, was broken into two or three pieces. The small bolts in the tower structure had broken as a result of hitting the crane. During laboratory tests in Germany, tiny cracks in the valley of the threads were discovered due to the carbon deposits, causing the fracture of the bolts because of the abnormally high hardness induced during heat treatment.

The bolts not only had to be manufactured once again but the failure also cost us a lot of money as the replacements had to be airfreighted to the jobsite in Egypt. We had to take another expensive lesson and therefore decided to create our own in-house heat treatment facilities so we could rigorously control the processes and protect ourselves from ever again facing the consequences of such mistakes.

Now we have our own cabin furnaces for bolts and studs up to two metres long in Class 10.9. We use a well type furnace for wind tower anchor bolts up to 3m long and a continuous mesh belt automatic quench and temper heat treatment line for smaller bolts, up to M30 x 200, and nuts. We no longer send any bolts or nuts to external companies for heat treatment.

Today, besides our hot dip galvanising plant, we have installed our own electro galvanising plant as well as a zinc lamella coating line. This means we do not need to send any of our bolts and nuts out of our premises for coating against corrosion.

We also decided to make some more investments into our test laboratory when we had problems with external laboratory tests, even though they were relatively minor. As time went on, we increased our laboratory testing equipment – so much so that our laboratory is now the best equipped in the bolt and nut sector in Turkey and we are the only manufacturer with laboratory accreditation to ISO EN 17025.

Over the years, we have received new test equipment for the growing needs of our global customers or we have developed equipment ourselves to meet our specific requirements. Today we hold the patent for and have the most powerful tensile tester in Europe at the Berdan laboratory. While the capacity of the biggest tensile tester in Turkey is 250 tonnes and stands 3.5m high, our patented device performs tensile testing up to 500 tonnes, utilising compression – and it stands just 1.5m high. Similarly, one of Europe’s most powerful torque testers, with a capacity of 30,000Nm, is in our laboratory.

Today Berdan is the only integrated fastener company in Turkey that can carry out notch impact tests at very low temperatures, down to -150°C. Thanks to our own surface coating facilities – for hot dip galvanising, electro galvanised coating and zinc lamination coating – we have achieved great success taking on unexpected orders and projects.

A prime example is Berdan Cıvata being called upon to use its fastener engineering experience to connect Europe and Asia – with the company supplying anchor bolts for the Çanakkale Strait bridge, after previously working on the Osmangazi bridge.

The Çanakkale Strait bridge (named Çanakkale 1915 bridge after Turkey’s historic victory in the region during WWI) is a 3.7km steel suspension bridge being built over the Dardanelles Strait in the Çanakkale province of Turkey. Located at the western end of the Marmara Sea, the bridge will connect the Lapseki District to the Gelibolu District (Gallipoli).

The consortium contracted to build the Çanakkale Strait bridge –
Daelim and SK E&C, along with Turkish companies Limak Holding and Yapi Merkezi – contacted Berdan Cıvata to manufacture steel anchor bolts and relevant fastening components due to the company’s experience within the industry.

Berdan Cıvata supplied 762 sets of M85 x 1,0178mm Class 10.9 of anchor bolts for the bridge, which once completed will have a central span of 2,023m and a total length of 4,608m – with space for three lanes of traffic in both directions. Berdan already has previous experience of supplying such a project after supplying the Izmit Bay Crossing suspended bridge (Osmangazi bridge), which opened in July 2016. The Osmangazi bridge has a central span length of 1,550m – currently making it the 2nd longest in Europe and 4th longest in the world.

We are very proud to be involved in the Çanakkale 1915 bridge project and we are already supplying products to help ensure the bridge opens on time in 2023 to coincide with the centenary of the Republic of Turkey.

Find Berdan Civata at fastener Fair Turkey on Stand 328

www.berdancivata.com

Content Director

Will Lowry Content Director t: +44 (0) 1727 743 888

Biog

Will joined Fastener + Fixing Magazine in 2007 and over the last 15 years has experienced every facet of the fastener sector - interviewing key figures within the industry and visiting leading companies and exhibitions around the globe.

Will manages the content strategy across all platforms and is the guardian for the high editorial standards that the Magazine is renowned.